Kompiuterio korpusas BitFenix, juoda sp.

The BitFenix Pandora ATX brings all the sought-after elements from the original Pandora to full-size ATX systems. Key features are the support for 360mm radiators and graphics cards up to 440mm. Aesthetics have taken precedence during the design process, as the Pandora ATX retains its little brother’s uniquely curved exterior, while special care has also been taken to ensure the interior shows off your hardware at its best through the side window.

Power and reset buttons are tastefully and non-intrusively backlit, while the side panel features an acrylic window. The Pandora ATX top panel starts with the front I/O, featuring dual USB 3.0 ports, dual audio jacks and dual USB 2.0 ports as well as power and reset buttons. The rest of Pandora ATX’s top cover consists entirely of a pop-off grille with a built-in dust filter.

Interior-wise, the Pandora ATX is designed to not only accommodate your high-end hardware, but to show it off as tastefully as possible. Full ATX motherboards are now supported, and up to seven 2.5” SSDs can be installed, or five 2.5” units plus two 3.5” HDDs. The PSU is hidden away in the bottom, behind the power cover, allowing for stealthy cable management and clean builds. This is further supported by a 20mm clearance between the off-side door and the back of the motherboard tray and plentiful tie strap mounts.

The Pandora ATX will comfortably house 360mm radiators, with one in the top or one in the front. For external watercooling needs, the case has rubber grommets above the rear exhaust fan for tube routing. Two easy-to-remove magnetically mounted dust filters are included with the Pandora ATX case –one for the three 120mm fans in the front, and one for the power supply, located in the bottom rear of the case.

Curved front panels are a unique feature of the Pandora ATX and so are their mounts. The leading edge is fixed with pushpins, and two insulating strips are installed to each panel. The trailing edge is fixed to the back of the case with thumb screws. The pump bracket is compatible with all existing pumps aimed at the PC market, while the SSD and HDD brackets are designed to be easy to install –with thumb screws.

Case type Midi-Tower

Form Factor ATX, Micro-ATX, Mini-ITX

Side panel Windowed

Colour Black

Main colour Black

Accent colour Black

Noise dampening No

Width (exact) 203

Height (exact) 558

Depth (exact) 510

Width 200 - 300 mm

Height 500 - 600 mm

Depth 500 - 600 mm

Material Plastic, Steel

Weight (exact) 9.66

Weight 8 - 10 kg

USB 4x

USB 3.0 2x

Audio output 1x

Audio input 1x

Internal 2.5" bays 2x

Internal 3.5" bays 3x

PCI slots 7x

Motherboard tray no

Remote no

Cable management yes

Front LCD/TFT display no

Filter yes

Power supply no

Power supply format ATX

Power supply position Rear Lower

Fans pre-installed 1x 120mm

120mm Fan 7

140mm Fan 4

Fan colour Black

Fan controller no

Card reader no

Front door no

Hot-swap no

Position I/O Cover

HDD anti-vibration no

Radiator-mounting 1x Triple (360mm)

Lighting no

Also included with all Pandora ATX cases is a foot to be installed separately to the rear, as well as a stylish aluminum front badge.

SPECIFICATION

- Materials: Steel, ABS

- Supported Motherboards: ATX, Micro ATX, Mini-ITX

- 3.5" Drive Bays: 3

- 2.5" Drive Bays: 2

- Front/Top I/O: 2x USB 3.0, 2x USB 2.0, 1x 3.5mm Mic-in, 1x 3.5mm Line-out

- Cooling Front: Max 3x 120mm OR 2x 140mm (Not Included)

- Cooling Rear: 1x 120mm (Included)

- Cooling Top: Max 3x 120mm OR 2x 140mm (Not Included)

- Expansion Slots: 7

- Highlights: One piece power cover and MB tray, Top, Front and Bottom Dust Filters, 360mm Radiator Support, 20mm Cable Clearance, Graphics Card Length up to 440mm, Maximum PSU length up to 220 mm, CPU cooler height up to 160mm.

- Dimensions: 203 x 510 x 558mm

- Weight: 9.66kg (net), 11.16kg (gross)